|
Defender Cartridge |
FF2 Pre Filter |
Full Face Mask |
Half mask Respirator |
Full Face ( Silicone) |
Half Mask Silicone |
Cartridge A1 |
Cartridge P3 |
Combination Cartridge |
Half Mask Double |
Half Mask Single |
FF1 |
FF2 |
FF2 Carbon Valve |
FF2 Valve |
FF2 Carbon Adjustable |
FF3 |
RN750089 - DEFENDER P3 (75SCP100)
Organic & Inorganic Gases & Vapours, Acid Gases & Particulates-
Defender Multi purpose cartridge for Organic Vapours, Chlorine, Hydrogen Chloride, Sulphur Dioxide, Hydrogen Sulphide (Escape), Hydrogen Fluoride, Chlorine Dioxide, Ammonia, Methylamine and Formaldehyde with P3 Efficiency Particulate Filter. (99.97% Minimum Filter Efficiency)
Precautions:
Not to be used in areas that are Oxygen deficient i.e. where Oxygen is below 19%.
Not to be used where the contaminant is IDLH.
Only to be used with North Safety Products approved Respirator
Back To Respiratory
Product: Twin Half Mask
Neoprene rubber half mask with 2 direct thread cartridge holders.
Comfortable low breathing resistance and easy fit headgear. Wide assortment of cartridges for various applications.
Physical Properties: Non allergenic moulded soft rubber. Elastic type head harness.
Quick release buckle on the elastic neck strap.
Standards: EN140
Uses: Can be used with the 7500 series filters, or as a Face piece with compressed airline apparatus CF2000 Plus.
Half mask Respirator approved for use against
Chlorine
Non-Oil Particulates
Mercury Vapour
Hydrogen Chloride
Ammonia
Sulphur Dioxide
Methylamine
Chlorine Dioxide
Organic Vapour
Cartridges:
RN75000 B1 (Inorganic gases & vapours)
RN65006A P1 (Dust Particles)
RN75006 P1 (Dust Particles)
RN75007 P2 (Dust Particles)
RN75008 P3 (Dust Particles)
RN750080 B1P3 (Inorganic gases & vapours & particles
RN750081 A1P3 (Organic Gases & Vapours & particles)
RN750083 A1B1E1P3 (Organic & Inorganic Gases & Vapours, Acid gases & particles)
RN75004 K1P3 (Ammonia & Organic ammonia derivatives & particles)
RN75001 A1 (Organic Gases & Vapours with boiling point >65 Degrees C)
RN75002 A1E1 (Organic & Acid Gases & Vapours)
RN75002 P1A1E1P1 (Organic & Acid Gases & Vapour, Sulphur Dioxide & Particles)
RN75003 A1B1E1 (Organic/Inorganic gases & vapours, Acid Gases & So2)
RN75003P2A1B1E1P2 (Dust Particles, Organic/Inorganic Gases, Acid and So2)
RN75004K1 (Ammonia & Organic ammonia derivatives)
RN75001P2A1P2 (Dust Particles & Organic Gases and vapours)
Particle filter classes 1, 2 and 3 according to different retention capacity
Pre-Filters:
RN75006A (Dust/Mist P1)
RN750010 (Spray paint / Mists P2)
RN750023 (Pesticide (P2)
Precautions: Not to be used in areas that are Oxygen deficient i.e. where Oxygen is below 19%.
Not to be used where the contaminant is IDLH.
Only to be used with North Safety Products approved 7500 series screw in cartridges.
Only to be used with the applicable cartridges to protect from the particular hazard.
Not to be worn with facial hair, i.e. no beards or moustaches.
Product: Single Half Mask
Neoprene rubber half mask with single direct thread cartridge holder. Comfortable low breathing resistance and easy fit headgear. Wide assortment of cartridges for various applications.
Physical Properties: Non allergenic moulded soft rubber. Elastic type head harness.
Quick release buckle on the elastic neck strap.
Standards: EN140
Uses: Can be used with the non combination 7500 series filters.
Half mask Respirator approved for use against
Chlorine
Non-Oil Particulates
Mercury Vapour
Hydrogen Chloride
Ammonia
Sulphur Dioxide
Methylamine
Chlorine Dioxide
Organic Vapour
Cartridges:
RN65006A P1 (Dust Particles)
RN75006 P1 (Dust Particles)
RN75008 P3 (Dust Particles)
RN75001 A1 (Organic Gases & Vapours with boiling point >65 Degrees C)
RN75004K1 (Ammonia & Organic ammonia derivatives)
Particle filter classes 1, 2 and 3 according to different retention capacity
Pre-Filters:
RN75006A (Dust/Mist P1)
RN750010 (Spray paint / Mists P2)
RN750023 (Pesticide (P2)
Precautions: Not to be used in areas that are Oxygen deficient i.e. where Oxygen is below 19%.
Not to be used where the contaminant is IDLH.
Only to be used with North Safety Products approved 7500 series screw in cartridges.
Only to be used with the applicable cartridges to protect from the particular hazard.
Not to be used with combination cartridges.
Not to be worn with facial hair, i.e. no beards or moustaches.
Product: FFP1SL Dust/Mist Respirator
Physical Properties:
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Low breathing resistance increases workers acceptance.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP1S SABS
SABS Homologation No: 33723 – Approval No AZ2003/45
Uses:
For use against fine respirable non-toxic dust and fibres.
For use up to 4 x OEL or 4 x APF.
Precautions:
Do not use in spray-paint operations.
Do not use in sandblasting operations.
Do not use for protection against asbestos.
Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches.
Back To Respiratory
Product: FFP2SL Dust/Mist Respirator
Physical Properties:
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Low breathing resistance increases workers acceptance.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP2S SABS
SABS Homologation No: 33723 – Approval No AZ2003/47
Uses: For use against low to average -toxic dust, fumes and aqueous mist.
For use up to 12x OEL or 10 x APF.
Precautions:
Do not use in spray-paint operations.
Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches.
Back To Respiratory
Product: FFP2SL Active Carbon Respirator with Valve
Physical Properties:
The exhalation valve offers lower breathing resistance for easier breathing which increases workers acceptance.
Activated carbon offers the additional protection against organic gas at nuisance levels.
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP2S SABS SABS Homologation No: 33723 – Approval No AZ2003/49
Uses:
For use against low to average -toxic dust, fumes and aqueous mist.
For use up to 12x OEL or 10 x APF.
For use against organic gases at nuisance levels.
Precautions: Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches
Product: FFP2SL Dust/Mist Respirator with Valve
Physical Properties:
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Low breathing resistance increases workers acceptance.
Exhalation valve offers comfort and durability.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP2S SABS
SABS Homologation No: 33723 – Approval No AZ2003/39
Uses: For use against low to average -toxic dust, fumes and aqueous mist.
For use up to 12x OEL or 10 x APF.
Precautions:
Do not use in spray-paint operations.
Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches.
Download To Specification Data
Product: FFP2SL Active Carbon Respirator with Valve
(FFP2SL Welding Mask with Adjustable Head Straps)
Physical Properties:
The exhalation valve offers lower breathing resistance for easier breathing which increases workers acceptance.
Activated carbon offers the additional protection against organic gas at nuisance levels.
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP2S SABS
SABS Homologation No: 33723 – Approval No AZ2003/48
Uses:
For use against low to average -toxic dust, fumes and aqueous mist.
For use up to 12x OEL or 10 x APF.
For use against organic gases at nuisance levels.
For use in Welding Applications.
Precautions:
Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches.
Back To Respiratory
Product: FFP3 Premium Respirator with Valve.
Physical Properties:
The exhalation valve offers lower breathing resistance for easier breathing which increases workers acceptance.
Activated carbon offers the additional protection against organic gas at nuisance levels.
A low profile mask offers a better fit with glasses and goggle.
A soft inner lining offers more comfort and less irritation.
Smooth, pre stretched head straps offer a good fit and comfort over the head and neck.
Contoured adjustable nosepiece offers maximum performance.
Standards: CE EN149 FFP3S
SABS Homologation No: 33723 – Approval No AZ2003/50
Uses:
For use against average to high -toxic dust, fumes and aqueous mist.
For use up to 50x OEL 0r 20 x APF.
Precautions:
Do not use in spray painting operations.
Do not use when concentrations of contaminant are unknown or immediately dangerous to life or health.
Not to be worn with facial hair, i.e. no beards or moustaches.
Back To Respiratory
